Dezhou Deqian HVAC Equipment Co., Ltd.

Greenhouse Unit Heater
PRODUCT PARAMETERS
The greenhouse unit heater is a heating device using medium/low-temperature hot water (55-75 degrees C) as the heating medium. This type of unit heater mainly consists of an external-rotor guard-covered fan, a heat exchanger, a grille outlet and a casing. The radiators are all copper tubes with aluminum fins; the heating medium enters through the lower pipe connection and exits through the upper one. Heat is conducted through the tube wall to the aluminum fins on the outer surface of the copper tubes and exchanged with the air. The impeller is driven by the motor, forcing the air to flow through the fins outside the tube rows, where it gains heat and its temperature rises.
Description
Installation, Use and Maintenance Instructions for the Cabinet Unit Heater
- When opening the packing box, be careful not to damage the unit heater and its paint layer with unpacking tools, and take out the accompanying documents in the box and keep them properly.
- During hoisting and transport, suspend the unit with steel cables through the lifting rings to prevent damage to the unit heater and its paint layer.
- Check the integrity of the unit heater before installation and wipe off the anti-rust grease.
- According to the heating medium selected for the radiator, the unit heater should be equipped with the corresponding supply and drainage piping: the water inlet is at the top and the drain outlet at the bottom. Note that sealed ball valves should be installed on both the hot water pipes and the return pipes.
- The motor wiring should make the fan impeller rotate clockwise (viewed from the air outlet direction).
- Before using the unit heater, carefully check the tightening condition of all connections; if any looseness is found, tighten it immediately.
- During operation, check the sealing of the radiator and its supply/drain pipes and the flexibility of all adjustment devices, and handle any fault promptly.
- When hot water is used as the heating medium, its pressure must be controlled within 0.03-0.6 MPa; overpressure use is strictly prohibited. When hot water is used, the water temperature is 45-75 degrees C.
- Before each operation, drain the cooling water and mixed gas in the radiator tubes, and start air supply after preheating for 5-10 minutes.
- After operation stops, drain the condensate in the radiator to prevent freezing. A small amount of hot medium or antifreeze can be allowed to circulate inside the radiator.
FAQs
We are a manufacturer of ventilation, air-conditioning, dust-removal and smoke-exhaust equipment. Our range covers fire smoke-exhaust fans, fire dampers and smoke-exhaust valves, aluminium air outlets and diffusers, ventilation ductwork and silencers, air-handling and fresh-air units, water tanks, cooling towers, seismic supports, and air-purification and kitchen oil-fume purification equipment.
Yes. Our fire dampers, smoke-exhaust fire dampers, smoke-exhaust valves and fire smoke-exhaust fans carry CCCF (3C) certification. For every fire-protection product we can supply national-level fire test reports together with the complete CCCF documentation package.
The company is certified to ISO 9001 (quality), ISO 14001 (environmental) and ISO 45001 (occupational health and safety) management systems, and holds AAA-grade certificates as a quality-assured, contract-honouring enterprise.
Our fan series includes CCCF axial fire smoke-exhaust fans, CCCF centrifugal fan boxes for fire service, pressurization supply fans, diagonal-flow fans, mixed-flow fans, axial fans, ceiling-mounted and floor-standing fresh-air ventilators, heat-recovery units, and finned-tube, rotary-wheel and heat-pipe air-handling units.
Dampers: CCCF automatic fire dampers, CCCF automatic smoke-exhaust fire dampers, CCCF automatic smoke-exhaust valves, manual balancing dampers, non-return dampers, pressurization supply outlets, multi-blade outlets, and CCCF smoke-exhaust outlets. Aluminium outlets: spherical jet nozzles, swirl diffusers, ceiling diffusers, weatherproof louvers, and single/double-deflection louvers.







